### Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

### Messages - pitney1

Pages: [1] 2 3 ... 5
1
« on: July 18, 2012, 02:30:18 PM »
I see the term adverse pressure gradient in many papers in fluid flows involving swirl. I have looked every where but I can not figure out what is adverse and favorable pressure gradients. What is meant by these terms? Adverse means unfavorable. What may be favorable for me might not be favorable for any one else. It is a relative term what does it has to do with pressure gradients!

2
##### Fluent / Tips and tricks to aid convergence in periodic flow problems with specified mass
« on: May 12, 2012, 11:53:18 AM »
Are there any tips and tricks to aid convergence in periodic flow problems with specified mass flow rates in FLUENT?

Thanks.

3
##### CFX / Is it possible to simulate an inviscid (Euler equation) flow in CFX?
« on: May 12, 2012, 11:47:47 AM »
Is it possible to simulate an inviscid (Euler equation) flow in CFX?

4
##### CFX / Re: Boiling calculations with an energy model for the vapour
« on: May 12, 2012, 11:44:35 AM »
Thanks!

5
##### CFX / Boiling calculations with an energy model for the vapour
« on: May 12, 2012, 11:43:21 AM »
Hi,

If either the Thermal Energy model or the Total Energy model is used for the vapour in a calculation using the RPI boiling model, then temperatures of the vapour phase are incorrect, being potentially either unphysically low or occasionally unphysically high.

Help!

6
##### Fluent / When I run the simulation I see that the particle tracks are incomplete.
« on: May 11, 2012, 11:10:06 PM »
When I run DPM with inviscid solution, all particle tracks are incomplete. Why? I am modeling inviscid flow solution and want to run DPM to track some particles. In the injection panel the particle velocity is set as zero. Interaction with continuous phase is turned ON. When I run the simulation I see that the particle tracks are incomplete.

7
##### CFX / What is the difference between Heat Flux and Wall Heat Flux in CFX-Post?
« on: May 11, 2012, 11:05:27 PM »
What is the difference between Heat Flux and Wall Heat Flux in CFX-Post?

8
##### CFX / How can I set a wall velocity at a fluid-solid interface in CFX?
« on: May 11, 2012, 11:03:35 PM »
I wish to set a wall velocity at a fluid-solid interface. How can I do this?

9
##### CFX / ERROR #001100279 has occurred in subroutine ErrAction.Message:Stopped in routine
« on: May 11, 2012, 11:01:30 PM »
When running the solver it crashed with the following error: ERROR #001100279 has occurred in subroutine ErrAction. Message: Stopped in routine ASS_GLOB_MPFCHT

10
##### CFX / How do I set an appropriate Physical timescale size for steady state calculation
« on: May 11, 2012, 10:59:01 PM »
How do I set an appropriate Physical timescale size for steady state calculations?

11
##### CFX / Rotating Domain and a Stationary Domain with rotating walls in CFX?
« on: May 11, 2012, 10:56:44 PM »
What is the difference between using a Rotating Domain and a Stationary Domain with rotating walls in CFX?

12
##### CFX / How can I apply my profile?
« on: May 11, 2012, 10:55:07 PM »
I have generated a velocity profile for my inlet boundary condition which uses a continuous fluid and at least one dispersed fluid. How can I apply my profile?

13
##### CFX / How to reduce the heating values of gases in a combustion simulation?
« on: May 11, 2012, 10:50:17 PM »
I would like to reduce the heating values of gases in a combustion simulation to represent a low combustion efficiency. How can I modify the NASA coefficients?

14
##### CFX / Fluid with a non-Newtonian viscosity dependence in CFX.
« on: May 11, 2012, 10:47:15 PM »
I would like to set-up a problem for a fluid with a non-Newtonian viscosity dependence. Are there any built in models for doing this in CFX?

15
##### CFX / why are my particle tracks so short when the injection velocity is low?
« on: May 11, 2012, 10:44:01 PM »
When using CFX 10.0 Solver why are my particle tracks so short when the injection velocity is low? The Particle Fate Diagnostics indicate "Exceeded time limit".

Pages: [1] 2 3 ... 5